What Is The Best Oil Fired Boiler


What Is The Best Oil Fired Boiler

Structural characteristics and rational utilization of the power of the furnace structure characteristic electric what is the best fired boiler hydraulic computing There are two methods for electrical boiler furnace: a designing new electric boiler, first by combustion requirements, according to the selected grate area of ​​the heat strength and the furnace volume heat intensity, determined baked and a preliminary discharge area is determined that the furnace volume, structure and size. Two boilers according to preliminary estimation method is recommended to determine the area of ​​the grate and furnace volume. Now Yaoan claim preliminary heat radiation heating surface arranged in the furnace, and the furnace structure is arranged drawn sketch, thereby performing the furnace structure characteristic calculation. When checking the conventional electric boiler furnace, if its structure is known, the furnace must be characteristic calculation means. Electric boiler furnace structure characteristic calculation means provide the necessary data for the furnace heat. After the furnace when the heat transfer calculation, checking furnace exit gas temperature is unreasonable, the institutions respond to the furnace and the radiation heating surface is arranged to be modified, and then calculated. The surrounding electric boiler furnace volume: Wall roof and around the center line of the plane (if the waterwall tubes covered with a refractory coating live bricks, where the surface is not Wall for Xianghuo arranged to the furnace wall surface of the wall. outlet chimney at the top of a row of tubes centerline) and a bottom surface of the plane. Unavoidable presence of various types of hydraulic oil flowing through the hydraulic valve when the pressure drop and flow loss, energy loss in this portion of the large proportion in the total energy loss. Therefore, a reasonable selection hydraulic, a pressure adjusting valve is also an important aspect of power loss reduction. Flow valve flow rate adjustment system according to the range of the minimum select and ensure stable flow can meet the requirements, the pressure in the pressure valve satisfied hydraulic equipment work properly, try to get a lower pressure. A reasonable choice of hydraulic oil. When the oil flow in the pipeline, will exhibit a viscosity, while too high viscosity, will have a greater internal friction, resulting in heating oil, while increasing the fluid flow resistance. When the viscosity is too low, easily lead to leakage, reducing the volumetric efficiency of the system, therefore, generally choose suitable viscosity and good viscosity-temperature characteristics of the oil. Further, when the oil flow in the pipeline, there is also along the local pressure loss and the pressure loss, so the design of the pipe line as short as possible, while reducing elbow.

More than 40 representatives from various industries across the country gather together in the group headquarters, systematic training and study and visit. Training excluded from the what is the best fired boiler system principles, common faults, maintenance meaning three aspects, the system elaborated from design, manufacturing to installation, commissioning, maintenance matters should be noted that several stages, delegates took the floor, the actual situation of the unit, asked in detail about the future direction of maintenance work required effort.

Construction of gas steam what is the best fired boiler steam requirements for the construction of a gas boiler requirements, gas steam boiler installation for the construction of the boiler room have certain requirements, must comply with national requirements in the construction process. Gas and steam 1, the construction of a gas steam boiler room requirements 1) boiler room must comply with the "boiler energy saving technical supervision and management regulations" and "industrial boiler room design specifications" requirement. Gas steam 2) boiler room should have sufficient light and good ventilation, have the necessary antifreeze measures. And boiler room should stay away from schools, housing and densely populated areas. 3) the position should be close to the boiler room heating equipment, in order to reduce head losses and heat loss from the hot oil piping circulating pump. 2, furnace heat carrier device is arranged in claim 1) the sump should be lower than the lowest position of the heat carrier furnace and heat system 1 m, in order to put the net organic heat boilers and systems, sump and furnace heat carrier spacing less than 5 m or separated by a partition wall. It should be fitted with a sump exhaust pipe, which exhaust pipe diameter should be large and specifications than the inflation tube. 2) position of the expansion tank should be higher than the other devices and the piping system, the system must be higher than the maximum bottom level 1.5 m. It should not be installed directly above any one boiler, organic heat carrier to prevent overflow cause a fire. 3) the sump vent pipe, expansion tank, should be connected to the outdoor safety. Can not be mounted on the vent pipe to the valve, to ensure that the tank, the expansion tank to atmosphere to ensure atmospheric pressure operation. 4) the high volume of the expansion tank should be greater than 1.3 times and all the organic heat carrier furnace heat the entire heating systems is at the operating temperature is increased due to thermal expansion of volume. 5) low volume tank furnace heat carrier to be less than 1.2 times the total amount of organic heat. 6) hot oil circulation pump should be at least four weeks for 0.5 m space, and the inspection to ensure the installation routine, the need for maintenance.

6 tons of chemical technology chemical parameters of natural gas steam what is the best fired boilers 6 tons of natural gas steam boiler technical parameters? Nowadays, people's food, clothing and housing are inseparable from the so-called chemical products. Chemical and chemical industry can be referred to as chemical, petroleum, pharmaceuticals, agriculture and so a place in the chemical industry. As chemical products processing, and various chemical plants, although there will be differences in the production process, but they can not leave some processing all the necessary equipment, steam boilers and other production. 6 tons WNS gas steam boiler, chemical production fast boiler dedicated premix combustion boiler technology, wings tubes, of FGR other new technology to increase the thermal efficiency of the boiler. Manufacturers increase production capacity. 6 tons of gas steam boiler technical parameters are as follows: Model Rated evaporation (6t / h) rated steam pressure (1.6.MPa) WNS6-1.6Y (Q) of natural gas, light oil and heavy oil fast filling. Of course, six tons of gas steam boiler is representative of WNS boiler, three times the structure, energy-efficient gas boiler. Six tons of steam boiler is mainly used in small-scale production and use is very diverse. Class 6 t good gas-fired boiler structure, take up less space, and a low one-time investment, high thermal efficiency.

Other Products