Oil Industrial Steam Boiler For Sale


Oil Industrial Steam Boiler For Sale

Inside the Fangkuai boiler plant, there is a special corrugated furnace bladder production line, which can be processed according to the computer setting mode. At the same time, this is also a unique processing technology of Fangkuai Boiler. The cost of natural gas fuel alone exceeds 5 million yuan per year. The corrugated furnace liner fired by this production line can not only increase the heating surface of the boiler, but also alleviate the damage caused by the thermal expansion and contraction to the combustion chamber, and greatly extend the service life of the boiler.

What are the technical parameters of the gas boiler boiler parameters are: 1, boiler capacity, which is the output Q, units of industrial steam boiler for sales are tons / hour representation. Hot water boiler for heat MW / h represents; 2, pressure P, the unit is Mpa; 3, steam (or superheated steam) Temperature q, in degrees Centigrade. Hot water boiler expressed in terms of outlet temperature and return water temperature. Another area of ​​the heating surface of each grate area, fuel type, fuel consumption, water temperature, total drag, with the wind (the wind drums) the amount of exhaust gas temperature and the like. The expression model are: the number of drum (e.g., single drum D, S, double drum); drum arrangement (transverse type H, the Z vertical type); combustion (chain L, G stationary grate etc.); a fuel type (coal a, gas Q, Y fuel, etc.); a steam boiler is usually "tons / h" or "t / h" is the capacity of the boiler. With "Mpa" or "MPa" (old unit of "kgf / cm 2" or "kgf / cm2") of the rated pressure of the boiler, it represents the temperature at the rated pressure saturated steam and superheated by "deg.] C" (Celsius) steam temperature. Thermal Efficiency Heat Transfer Fluid is a boiler furnace or a thermal transfer process, heat is absorbed by water, steam or thermal oil, accounting for complete combustion of the fuel into the boiler heat released percentage capacity of 1t / h steam boiler, i.e. It indicates that the boiler may be over 1 hour into water of 1 ton capacity of saturated steam under pressure; 0.7MW of such water heaters and furnaces heat Transfer Fluid representations may generate heat corresponding to 0.7MW power over 1 hour ( equivalent to one ton of steam heat). Two water boiler is the heating means for the hot water boiler working fluid. Usually "MW" (MW), with the old unit "when Wan kW /" or "million kcal / h", namely "104kcal / h" is the capacity of the boiler, with "Mpa" represents the rated pressure of the boiler, with "℃" the hot water temperature.

Pressure fire operations and precautions Henan fast boiler's industrial steam boiler for sale Xiao Bian told you about the operation of steam boilers and pressure fire precautions and stainless steel high temperature magnetic pump structural characteristics 1. pressure steam boiler fire steps of (1) to reduce boiler load, according to the length of time of shutdown, the seam thicker, the thickness is generally not more than 200 mm, suitable to accelerate the speed of the grate. (2) to the slag is thickened seam about 1 mm from the stop grate rotation, the drum is stopped, the operation of the induced draft fan, blowing off a small segment of the regulating plate stopper and dampers qs, relying on natural ventilation to maintain coal the lean-burn, the sewage, boiler water level will rise to the maximum allowable level. If the fire burn coal gate, grate can be switched on again, the coal-fired back, a distance. (3) the recovery boiler needs to run, as long as the opening lead, a blower, to adjust the smoke, and the wind baffle plenum segment adjusting the opening degree of the shutter, the adjustment of combustion steam boiler seam thickness to be normal, start grate, can be restored run. 2. Note the use of a steam boiler (1) before starting Check power supply voltage, there are unusual circumstances water, close the drain valve opens the water supply valve, check whether the pump stuck, stuck if the pump, remove the fan cover, rotation of the motor shaft to the flexible state to boot. (2) When the steam boiler maintenance or replacement of parts, turn off the power to avoid live work dangerous. (3) electronic control box, pump motors and other parts should avoid damp water to prevent burning boiler should pay attention to keep clean. (4) steam boilers in accordance with quality requirements, when using the apparatus sure to install a water softener, the water softener is not used because the boiler may cause fouling, may cause serious squib, shortening the life of the boiler. (5) Please note that when using sewage. And at least once a day with a discharge pressure of between 0.1MPa to 0.15MPa discharge may be prevented clogging of pipes, sewage should be properly connected, to guard against burns. Stainless steel high temperature magnetic pump structural features: a sliding bearing magnetic pump sliding bearing materials impregnated graphite, PTFE and engineering ceramics. Because of engineering ceramics has good heat resistance, corrosion resistance, abrasion performance, so the sliding bearing magnetic pump more use of engineering ceramics production. Because of engineering ceramics are brittle and expansion coefficient, so the bearing clearance is not too small, so as not to hold the shaft accident. Since the magnetic pump in order to lubricate sliding bearing medium conveyed, it should be used depending on the medium and conditions, making use of different materials bearing. 2. Cooling lubricating fluid flow control pump operation must be flush cooling internal friction annulus region between the sliding bearing and the magnetic rotor and the containment shell with a small amount of liquid. Coolant flow rate is typically 2-3% of the design flow of the pump, the annulus area between the inner magnetic rotor of the eddy current generated spacer bush high heat. When enough cooling lubricant or flushing holes poor, clogging, the medium will result in a temperature above the operating temperature of the permanent magnet, the inner magnetic rotor gradually loses its magnetism, the magnetic force actuator failure. When the medium is water or water-based liquid, the temperature rise can be maintained in the annulus region of 3-5 deg.] C; or when the medium is a hydrocarbon oil, allows the annulus region of the temperature was maintained at 5-8 ℃. Henan is committed to fast boiler steam boiler manufacturing, product quality, reasonable prices and widespread industry praise, if you have any needs, please contact us!

Ningde gas oil horizontal industrial steam boiler for sale steam boiler in the process of selecting our chosen medium, many questions will be met. Here, we have to talk about with small series. Main steam boiler steam boiler cost expenses, and costs burner, random (circulation pump, control panel, valves) the cost thereof. Determine the cost of steam boiler reason, the main cause for indulgence: product, respectively, factories, skills development, testing, planning, selection and other steel products. Among them, the best should pay attention to the following reasons: ⑴ strength of the manufacturer's plant productivity, it is likely to decide the quality of the product. Because all a productive company, excluding occupy a larger market share, release the right amount of experience. Han, secondly, the power of professional design products. Planning strength size for product quality implications are enormous. A direct impact on the product in the future with stability, energy efficiency, safety, and good operating standards. ② selection of quality metrics steel, steel is the core product development. Professional authoritative standard steel steam boiler is to ensure effective sealing of the firm. There are some small factories with substandard or use non-standard steel products will result in steam boilers, poor stability, high operating costs, in addition there is a certain security risk for customers, when even save enough to get the money, but worth the candle. 3 Development of an automatic steam boiler standards development process, cutting, plate bending, cutting, should pay attention to the best skills. These three techniques, the comparison must be to, manual control, the use of automatic development, highlights prominent relatively common. Because ISO production, with advanced precision, minimal mistakes. This is also the key reason for the large steam boiler products product, far better than small products. Because it, the results of research, planning and more closer connection strength, together with good access to authoritative standard setting. d detection criteria many factories in China, a lot of time there will be no steam boiler products through rigorous factory part of the evaluation assessment. Pressure to complete, even if the professional products. This is certainly a very fulfilling responsibilities. Professional detection criterion must probably comprising: a pressure test, the test inert gas, welding gap detection, detection of the seal, and the test run. Can be neglected, balanced. The only way to ensure that customers have a grasp of professional products to customers in the future when used to eliminate non-compliant products have generated, the impact to the customer's daily production and business activities. ⑸ quality after-sales 60% of small factories, there will be no after-sales. After-sales support are entrusted proxy to master. However, 60% of agency staff, there are few professional standards of the strength of the team. After generating non-compliance, it will have dragged on, or use the results often can not be solved. To sum up, that is, the cost of a steam boiler, the influence of reason. Normal in terms of strength, good steam boiler product cost, plus the steam boiler burner, the basic, 700KW, 10 million and decided.

Other Products