Natural Gas Fired Boiler In Iran

During installation, the technical team fast fired boiler in iran plant according to the specific needs of our environment, our rational arrangement of stacks, pipes, and other auxiliary equipment, let us bring a lot of convenience in the latter part of the course. Fang fast responsible attitude also gives us impressed, sent a technical team for installation, commissioning and training to us, let us rest assured, peace of mind, peace of mind. --customer feedback

Analysis and pressure steam fired boiler in iran burning issues of excessive treatment: this kind of boiler steam boiler, because it is an important site for the product, so in their knowledge and understanding of the, at least, should achieve a comprehensive and specific to this extent, so in order to further the product site, rather than just stay on the surface, and then, in the use of the product, there is a good use of effects. Therefore, in order to achieve the above objectives, the following will continue this topic, which reads as follows. 1. steam boiler, which is in use, whether the boiler must first obtain use permits, and then to use this kind of boiler? In addition, if classified according to their fuel, then, in particular, which has several? Steam boilers, because it belongs to special equipment, therefore, can not be directly used, relevant departments should first obtain use permits issued by the boiler, and then to use steam boilers. In addition, this kind of boiler, if classified according to the type of fuel, then, can be divided into three electric steam boiler, gas steam boiler and steam boiler fuel.

Increase productivity fired boiler in iran system must first be optimized for verification, including the entire steam system for a complete analysis, and focus on some of the energy waste places. Via check can often find opportunities to save energy, increase productivity, and environmental protection have a positive contribution of. Check includes a steam generation, distribution, use and condensate recovery. The main steam waste requiring special attention place: exhaust gas boiler: boiler efficiency emissions system the most important indicators, the loss of energy is the most important place. Combustion air: general air enters the combustion furnace of the genus room temperature, require a lot of heating energy, i.e., the most commonly used power saving mode using a high temperature exhaust gas to preheat the combustion air of boiler, boiler efficiency can be significantly improved. The fuel / air ratio: Proper oil / gas mixture can only complete combustion, if the lack of air, combustion is incomplete, not only smoky pollution, environmental protests caused nearby residents, and easy carbonized grease gun and boiler heating tubes affect performance. If excess air is formed wasted energy, reducing boiler efficiency. Via the oxygen content of the tail gas can appropriately adjust the oil / gas ratio. Oil-fired boiler exhaust gas which content 3%, i.e., the excess air of about 15%, as the standard combustion control.

Three kinds of ventilation fired boiler in irans often used at runtime to be continuously supplied to the boiler the combustion air required, and the resulting flue gas continuously drawn, a process called draft process of the boiler. Once the venting is stopped, the boiler will stop running; usually mechanically ventilated, i.e., by means of a pressure head generated by the fan to overcome smoke flow resistance of the duct. Mechanical ventilation currently used in the following three. A negative pressure ventilation chimney addition to using, the former also mounted chimney draft fan to overcome the resistance of all of the smoke, the air duct. This small capacity of ventilation, smoke wind resistance is not so large boiler system is more applicable. Second, while a balanced draft and induced draft fan blower mounted in the boiler smoke, air system. Port to the suction passage into the furnace from the wind (including through an air preheater, and a fuel combustion device layer) overcome the resistance of the entire duct fan; furnace outlet to the outlet stack (including a negative pressure outlet furnace, boiler slag tube after anti heating surface portions of the device and the dust removal) all by flue draft fan to overcome the resistance. This ventilation can effectively into the air, and the furnace flue boilers and all run under negative pressure, boiler room of the safety and health conditions better. If compared with negative pressure ventilation, boiler air leakage is small. Currently in heating boilers, the most balanced ventilation. Third, the only positive draft blower mounted in the boiler smoke in the air system, with its head against the resistance of all the smoke duct. Then the furnace and flue boiler are all working under pressure, and thus the furnace wall and door units are required tightly sealed to prevent leakage of flames and smoke high temperature hurt. This ventilation improves the strength of the heat of combustion furnace, boiler smaller volume equivalent capacity. By eliminating air leakage boiler furnace, flues, and improve the thermal efficiency of the boiler. Positive pressure ventilation, currently has applications in the oil and gas boilers. Boiler draft ventilation is generally balanced and positive pressure ventilation. These are the three common boiler ventilation method, in the process, to constantly add fuel, while also promptly clean up the burned ashes.