High Quality 1T Diesel Oil Boiler


High Quality 1T Diesel Oil Boiler

Burner and flue installation and electrical installation and the fuel supply system of the burner 1, burner 1) before installation read "burner manual", according to the installation requirements. 2) Burner mounting flange, the middle requirements, to ensure the burner to the high quality 1t diesel boiler flue gas does not leak at the interface. 2, the installation of fuel supply system (see schematic) Note: To prevent a fire caused by generation of static electricity in the fuel tank, the tank should have a good grounding. 1) supply system tank top tank top-feed system suction recommended distance between the back plane and the tubing inside diameter of the oil pump axis, the total length of the suction pipe Hm, m, no greater than DL6-34DL40-75DL100-250Di = 10mmDi = 14mmDi = 16mm0.51.03030401.535452.03535452.540503.0404050 Notes: (1) when there is an elbow or valve on the suction pipe, each of the length of the suction pipe to be minus 0.25m. (2) Di recommended internal diameter suction pipe and return pipe. 2) the distance between the bottom of the tank bottom of the tank supply system supply system pipe inner diameter recommended oil pump axis and a plane, the total length of the suction pipe Hm, m, no greater than DL6-34DL40-75DL100-250Di = 10mmDi = 14mmDi = 16mm1.03030401.535452.03535452.540503.04040504.045 Notes: (1) when there is an elbow or valve on the suction pipe, each of the length of the suction pipe to be minus 0.25m. (2) Di recommended internal diameter suction pipe and return pipe. 3, gas pipe installation requirements Burner gas line itself has been connected, the intake port, the intake pipe bends should be minimized and good sealing performance requirements, to prevent leakage. (Iv) a chimney installation, to prevent leakage, the leakage of smoke, to prevent smoke inhalation chamber. 2, a vertical mounting, a right angle bend bends should be avoided. 3, the top of the chimney must be water-resistant measures. (E) mounting a power switch with electrical connection box 1, the power switch should be considered easy to operate, away from heat, fixation, meet the design requirements. 2, the use of 220V (380V), 50HZ power source, and a ground line. 3, voltage instability in the region use, should be safe regulators. Or affect the normal operation of the combustion engine. 4, the power cord to the electrical box must be connected in strict accordance with the requirements, otherwise, there will be dangerous!

The fuel of the oil-fired high quality 1t diesel boiler is the fuel (such as diesel oil, kerosene, etc.), the fuel of the gas-fired boiler is gas (such as natural gas, city gas, biogas, etc.), depending on what fuel the boiler burns, the equipment is called the burner. The boiler with gas burner is called gas boiler, the boiler with oil burner is called oil fired boiler. The difference between oil fired boiler and gas fired boiler is what fuel burners are used.

Fang Group R & D center was officially opened fast approaching New Year party quickly ushered in a large group wedding - R & D Center was officially launched. VIP dealers from Beijing, Tianjin, Hunan, Sichuan, Fujian, Heilongjiang and Xinjiang invited to participate in the ribbon-cutting activities.

What are the three common high quality 1t diesel boiler combustion? Urban coal-fired boiler has been difficult to solve, because especially small coal-fired boilers type cluttered and more widespread particularly difficult to handle. On the one hand burning low power, on the other hand is more a waste of resources. Under the requirements of environmental protection requirements, many cities in the relevant part of the requirements necessary gas (oil) boiler retrofit or replacement of 10t / h coal-fired boilers. The transformation of the former needs to focus attention to the following questions: whether the site is useful region of central heating boiler heating of small alternative program. The useful life and corroded boiler, if the boiler by Zhengzhou fast boiler or other professional testing organization to determine the useful life of less than five years, the transformation of value is not high. Determine whether the laying of gas pipeline convenience, liquefied petroleum gas or other fuel supply and transportation issues. Comparing the cost of renovation and equipment manufacturers advantages and disadvantages, in determining the needs of the transformation plan in compliance with these principles. Selection of fuel. Under the premise of fuel sources have, the most economical natural gas pipelines, liquefied petroleum gas, followed by a final light diesel oil. Also, consider the surrounding environment from fire and explosion safety. In general, the system and the soda boiler pressure parts and preferably not modified to adhere to the original power, are demand, under conditions not substantially change the pressure member, than the original power increased by 10% to 20%. Boiler pressure parts for major changes in the program desirable. The transformation process is necessary to ensure the safety of boiler pressure parts of (mostly small commercial general pressure boilers), followed by incineration system to ensure the safety factor, the decline in the risk of explosion, fire accidents. Recognize the transformation of the planning process, in a timely manner, the environmental protection, the gas company, fire department, urban construction and timely communication with the boiler section to monitor and ensure the transformation plan can proceed smoothly. When the boiler is burning way during boiler selection will take into account an element, the following three common boiler burning approach advantages and disadvantages brief analysis cf: 1 Decentralized incineration strengths: this way is not burning premixed, but the gas nozzle mouth dispersed with each other, and then burning it. Incineration relatively simple way, as more stable as compared to the flame. Disadvantages: Due to a longer flame, it is prone to the phenomenon of incomplete burning, more carbon monoxide and nitrogen oxides will occur, it is not conducive to the use of full-fired boilers, to improve the thermal power of the boiler, and the boiler emissions standards are difficult to reach. 2. premix approaches incineration advantages: premixing air and gas, a multi-way heat radiator, to improve the strength of heat transfer. Strengths of this approach is that the burning of the burning flame is more clear, and the higher heating power. Disadvantages: incineration requires precise ratio premix burning rate is fast, uniform burning radiant heat transfer full power high flame temperature below 1200 deg.] C, all NOx completely burned and the occurrence of low flue gas temperature, condenses, good heat recovery and high power. 3. No flame burning incineration space before incineration approach uniform mixing with the gas in the gas boiler. When using this approach, in the process of incineration gas in the oxygen demand is not made in the ambient air demand, only needs to achieve instant complete incineration air mixture reaches the incineration zone. Approach in the selection of incineration, incineration demand for the advantages and disadvantages of different approaches, carried out mutatis mutandis selection, a good way is also advantageous burning boiler to reach plenty of incineration, thermal power increase, decrease the role of emissions, and therefore, it is important to choose carefully.

Other Products