Gas Fuel Hot Water Boiler Price


Gas Fuel Hot Water Boiler Price

Car accessories types of complex processing, such as the interior wall Peng, floor, seats, instrument panels, sound systems, many processes required in a high temperature environment, the temperature becomes optional metrics wind Visteon fuel hot water boiler price. It is reported that Dongfeng Visteon existing boiler equipment can not reach the growing production needs, the introduction of fast boiler production of two parties often piezoelectric hot water boiler (CWDR1.8-95 / 70-II) in 2017.

Mill steam boilers to reduce pollution which method 1, leak checking and maintenance of protection: 2 mm steam leakage will cause energy losses of more than 10 tons of coal each year do? When you do not use it, you can turn it off to save energy. For water, steam and compressed air leak survey and routine maintenance, cost very little. 2, the non-contact cooling water in repeated use: Since the non-contact cooling water temperature and the quality is very good, it can be reused for desizing, scouring, rinsing and other processes. Three best source of cooling water is regenerated: sintering machine, a pre-link and compressor systems. The plant water recovery system may be installed, pipes, valves, storage tanks, and control systems. 3, reuse of steam condensate: textile mills require large amounts of saturated water vapor in the dyeing process, wherein a portion of the condensate is converted to its high temperature and purity. Water can be pumped back to the boiler to form a new steam. For those who buy steam from suppliers, or boiler is located away from the dyeing process, the condensate can be used as water washing or desizing. 4, pre-treated wastewater reuse Procedure collected bleaching, mercerizing machine, the water can be reused in other programs, there is no direct discharge of wastewater. 5, hot wash water is recovered from the hot gas in the dyeing process, large amounts of hot water are used to wash. Heat the washing water can be collected by the system plate heat exchanger to preheat the water to be sent to the next washing. 6, pre-screened coal enterprises should introduce screening spiral coal boiler technology to selection of raw materials. It is possible to improve the media tell the good, the bad quality of proportion, to avoid loss of small volumes of coal and coal calorific value. 7, maintaining steam traps traps can help maintain effective delivery of the steam plant. The valve is removed from the steam pipe and prevent further condensation water, so as to avoid heat loss and reduce fuel consumption. 8, pipe insulation pipes, valves and flanges, valves and flanges experience hot waste of resources, reducing efficiency. Steam delivery device insulated to prevent vapor loss is an inexpensive, energy-saving method of .9, the heat recovery boiler chimney smoke at a temperature of 360 deg.] C, and sometimes directly discharged into the atmosphere, there is no heat recovery. In fact, this heat can be used to preheat boiler water, steam or create a new steam system. 10, optimization of compressed air systems consume a large amount of compressed air in many parts of textile machines Mills. These instruments are prone to leakage, particularly in a threaded joint, rubber joints, valves, automatic regulator, the inflatable device and the old gasket. In addition, the use of compressed air pressure is usually based on the maximum pressure setting; reduce this pressure is feasible and would not have any negative impact manufacturing.

Method for implementing energy saving and environmentally friendly features a method of environmentally boiler boiler: the boiler flue gas heat recovery boiler is an important way of saving large flue gas calorific value, only the latent heat of vaporization of water vapor is sufficient to boiler feed water is preheated to above 100 ℃ not only can be used for boiler feed water, the excess water can also be used to heat domestic hot water. Fuel, boiler exhaust gas heat loss of about 8% to 16%, about 1% heat loss sewage, furnace heat 1 to 2%, 1% incomplete combustion, effective utilization of heat of about 80% to 91%, the flue gas includes N2 accounted 68%, Co211%, H2O16%, O24%, SO22PPM, NOx80PPM. If the exhaust gas temperature of 200 ℃, high total heat recovery through the heat exchanger, flue gas temperature can be lowered to 70C or less, the boiler feed water to raise to 20 ℃ 85 ℃, saving a lot of energy. Meanwhile, since the oil and gas, especially natural gas sulfur content less, the content of SO2 in the flue gas is very low, most of them are dissolved into condensed water discharged flue gas, the combined flue gas heat recovery devices are made of stainless steel, to ensure a reliable means corrosion resistance, and therefore the service life of the entire device more than 5-6 years. By monitoring, the indicators have reached the national environmental standards. Environmental regulations described boiler drum assembly welds should be: the drum longitudinal and circumferential weld head assembly or assembly welding seam characteristics weld two elements should satisfy the following requirements: the longitudinal weld seam or stitching head deviation of the actual edge on both sides of the steel sheet is not greater than 10% of the nominal thickness, and not more than 3mm; when the thickness is greater than 100mm, of not more than 6mm. Deviation of the actual edge seam on both sides of the steel sheet ring is not greater than 15% of the nominal thickness plus 1mm, and no greater than 6mm; when the thickness is larger than 100mm, no more than 10mm. Two abutting element or plate have different thicknesses and the edge of the book cut, treated according to the same plate thickness, the above-described nominal sheet thickness means; butt plate of different thicknesses, but with no thinning, the nominal thickness of the aforementioned finger planks . Any difference between the maximum inner diameter of the same cross-section and the minimum inner diameter of the drum should be not more than 1% of the nominal inner diameter. Angularity drum longitudinal seam should be no greater than 4mm. If the pressure detecting element via a weld joint defects found unacceptable, welding unit shall find out the reason, the development of a viable repair program to rework. Before welding defects should be completely removed. After welding, welding zone should be done appearance inspection and nondestructive testing. Heat treatment after welding element requirements, should be done after the welding heat treatment after welding. Rework the same position should not exceed three times. Repair parts, frequency and circumstances shall be deposited in the boiler repair product technical file.

Pressure boiler furnace designed to fully consider the characteristics of the fuel pressure boilers body member are two main drum and furnace. Also known as the furnace combustion chamber, fuel combustion for space. The solid fuel on to the grate, referred to as a fire bed combustion furnace Stoker, also known as fire bed furnace; solid fuel furnace liquid, gas or pulverized, is injected into the combustion chamber is called the fire chamber burner, also known as the furnace fire chamber; air coal particles burn hold it was boiling, and the furnace is inferior fuel suitable for combustion is called fluidized bed furnace, also called fluidized bed furnace; coal particles so that an air flow rotated at high speed, and strongly called fire cylindrical cyclone furnace hearth. The overall structure of pressure boilers and boiler auxiliary equipment including two parts. Boiler furnace, drum, burner, water wall superheater, economizer, air preheater, and the furnace wall, etc. The main frame member constituting the core part of the steam production, called boiler. Furnace design needs to fully consider the characteristics of the fuel used. Each boiler should be fueled with the original design of the fuel. Boilers running economy and reliability are likely to vary greatly reduced when using the characteristics of fuel combustion. And the natural circulation drum is repeatedly forced circulation boiler receiving feedwater to the economizer, the coupling cycle and supplying saturated steam superheater cylindrical vessel. Simplified drum made from high quality steel plate, is one of the heaviest components of the boiler.

Other Products