10Kg Pressure Oil Steam Boilers


10Kg Pressure Oil Steam Boilers

Combustion gas treatment unit and a fault, gas boiler burner ignition misfire rod reasons: 1, the ignition bar gap interposed carbon residue with oil. 2, ignition rods fragmentation. moist. Leakage. 3, the distance between the ignition does not stick, too long or short. 4, ignition rods Insulation damage, short to ground. 5, ignition cable and transformer failure: cable, connector damage caused by a short circuit during ignition; transformer break or other fault occurs. Measures following five: Clear, renewal, adjust the distance, change and switching transformer. Second, gas boiler, but spark ignition rods misfire reasons: 1, the cyclone disc space ventilation is blocked carbon, poor ventilation. 2, dirty oil nozzle clogging or wear. 3, the throttle angle is set too small. 4, the firing bar from the leading edge from the oil nozzle tip inappropriate (too protruding or retracted) 5, the first solenoid valve is an oil debris blocking gun (gun small kerosene). 6, oily or too viscous to flow easily clogged or the oil filtration system the valve is not opened, so that insufficient suction pump, oil pressure. 7, the filter pump itself blocked. 8, the oil more water (boiling abnormal noise within the heater). Measures are: Clear; first wash, such as not renewed; turndown test; adjusting the distance (in 3 ~ 4mm as well); Remove cleaning (cleaning the parts diesel); Check tubing and oil filters, insulation equipment ; remove peripheral screw pump, carefully remove the cover inside out oil network, with immersion oil; renewal of the test oil. Third, when the gas boiler and turn the fire a small fire normal, off, or flashing instability reasons: 1, the air volume damper setting fire too. 2, oil fires micro switch valve (damper outermost that group) inappropriate setting (set throttle air flow rate is greater than the fire). 3, oleaginous easy to spray viscosity is too high (heavy). 4, and the nozzle plate spacing cyclone inappropriate. 5, fire nozzle worn or dirty. 6, the preliminary fuel tank temperature is too high, so that the steam not smooth oil pump oil feed. 7, fuel oil boiler water. Action: Test gradually reduced; heating temperature; adjusting the distance (between 0 ~ 10mm); clean or replace; approximately set to about 50 deg.] C; or drain oil change. Fourth, the noise increases gas boiler burner reasons: 1, cut-off valve is closed or the passage into the fuel shortage, an oil filter blockage. 2, the oil inlet temperature is low, the oil viscosity is too high or the temperature is too high the pump inlet. 3, oil pump failure. 4, fan motor bearing damage. 5, dirty fan impeller. Processing methods: ① the oil line check valve is open, if the oil filter is working properly, the filter cleaning pump itself. ② heating oil or reduce the oil temperature. ③ Replace the oil pump. ④ replace motor or bearings. ⑤ cleaning fan wheel.

Some knowledge boiler Introduction: boiler is an energy conversion device, the energy input to the boiler chemical energy, electrical energy, a boiler with a steam output of the fuel in the constant heat, high temperature water or organic heat carrier. Today introduced are several little knowledge about the boiler. 1, a way to improve the efficiency of the boiler A which:? ⑴ low heat losses: prevent heating surface fouling and coking, the rational use of the burner, controls the blower inlet air temperature, water temperature of attention to the impact, into the furnace to avoid excessive wind note impact milling system operation; ⑵ mechanical incomplete combustion to reduce heat loss: rationally adjust the fineness of pulverized coal, the excess air ratio control of appropriate, attention combustion adjustment; ⑶ quality assurance fired boilers; ⑷ reduce soda losses: guaranteed boiler quality water supply, installation and maintenance to improve the quality of the steam separator means, to maintain the operation of the boiler load, the water level, steam pressure and other parameters of stability, so that the boiler water separation apparatus operating under normal conditions; ⑸ index management adhere to the small boiler. ? What are the reasons boiler fire answer: ⑴ low boiler load, low temperature furnace, combustion temperature, combustion oil investment is not timely; ⑵ poor coal quality, low volatile matter, ash is too large; ⑶ air volume to adjust properly, once too high wind speed, wind powder imbalance, the excess air ratio is too large; ⑷ excessive negative pressure maintaining furnace; ⑸ bunker powder level is too low or fallen powder to the powder to make the powder unevenness; ⑸ large depression coke furnace, disturbances in the furnace is too large; ⑹ ash, coke playing time is too long, especially large caused by cold air leakage into the furnace temperature drops to a low load; ⑺ blast furnace tube, a large number of soft drinks into the furnace; ⑻ fire protection action; ⑼ device malfunction, such as sending, fan, tripping of mill, Auxiliary disappeared.

Pressure fire operations and precautions Henan fast boiler's 10kg pressure steam boilers Xiao Bian told you about the operation of steam boilers and pressure fire precautions and stainless steel high temperature magnetic pump structural characteristics 1. pressure steam boiler fire steps of (1) to reduce boiler load, according to the length of time of shutdown, the seam thicker, the thickness is generally not more than 200 mm, suitable to accelerate the speed of the grate. (2) to the slag is thickened seam about 1 mm from the stop grate rotation, the drum is stopped, the operation of the induced draft fan, blowing off a small segment of the regulating plate stopper and dampers qs, relying on natural ventilation to maintain coal the lean-burn, the sewage, boiler water level will rise to the maximum allowable level. If the fire burn coal gate, grate can be switched on again, the coal-fired back, a distance. (3) the recovery boiler needs to run, as long as the opening lead, a blower, to adjust the smoke, and the wind baffle plenum segment adjusting the opening degree of the shutter, the adjustment of combustion steam boiler seam thickness to be normal, start grate, can be restored run. 2. Note the use of a steam boiler (1) before starting Check power supply voltage, there are unusual circumstances water, close the drain valve opens the water supply valve, check whether the pump stuck, stuck if the pump, remove the fan cover, rotation of the motor shaft to the flexible state to boot. (2) When the steam boiler maintenance or replacement of parts, turn off the power to avoid live work dangerous. (3) electronic control box, pump motors and other parts should avoid damp water to prevent burning boiler should pay attention to keep clean. (4) steam boilers in accordance with quality requirements, when using the apparatus sure to install a water softener, the water softener is not used because the boiler may cause fouling, may cause serious squib, shortening the life of the boiler. (5) Please note that when using sewage. And at least once a day with a discharge pressure of between 0.1MPa to 0.15MPa discharge may be prevented clogging of pipes, sewage should be properly connected, to guard against burns. Stainless steel high temperature magnetic pump structural features: a sliding bearing magnetic pump sliding bearing materials impregnated graphite, PTFE and engineering ceramics. Because of engineering ceramics has good heat resistance, corrosion resistance, abrasion performance, so the sliding bearing magnetic pump more use of engineering ceramics production. Because of engineering ceramics are brittle and expansion coefficient, so the bearing clearance is not too small, so as not to hold the shaft accident. Since the magnetic pump in order to lubricate sliding bearing medium conveyed, it should be used depending on the medium and conditions, making use of different materials bearing. 2. Cooling lubricating fluid flow control pump operation must be flush cooling internal friction annulus region between the sliding bearing and the magnetic rotor and the containment shell with a small amount of liquid. Coolant flow rate is typically 2-3% of the design flow of the pump, the annulus area between the inner magnetic rotor of the eddy current generated spacer bush high heat. When enough cooling lubricant or flushing holes poor, clogging, the medium will result in a temperature above the operating temperature of the permanent magnet, the inner magnetic rotor gradually loses its magnetism, the magnetic force actuator failure. When the medium is water or water-based liquid, the temperature rise can be maintained in the annulus region of 3-5 deg.] C; or when the medium is a hydrocarbon oil, allows the annulus region of the temperature was maintained at 5-8 ℃. Henan is committed to fast boiler steam boiler manufacturing, product quality, reasonable prices and widespread industry praise, if you have any needs, please contact us!

National response to control air pollution and maintain policies favorable ecological environment; effective control of thermal power, steel and other key industries, the total amount of atmospheric emissions of major pollutants, Ningxia implementation of thermal power, steel and other industries, especially air emission limits for pollutants in the metropolitan area of ​​Yinchuan.

In particular emission limits refers to higher standards than the national emission of pollutants, more stringent emission requirements; implementation of special emission limits, implementation of key industries mentioned standard transformation is one important way to reduce pollutant emissions. Yinchuan City metropolitan area including Yinchuan, Shizuishan City, Wuzhong City Litong District, Qingtongxia City Administrative Region and Ning Dong Energy and Chemical Base (core area). Perform particularly air pollutants emission limits in all of these areas of thermal power, iron and steel, cement, petrochemical, non-ferrous metals, chemical industry, coal-fired boilers and sulfur dioxide, nitrogen oxides, particulate matter.

Since the execution time is tentatively scheduled for January 1, 2019, for the present, China has not yet specified air pollutants emission limits in particular industry, to be the relevant standards or modified, re-implemented.

For enterprises, especially not achieve emission limits of air pollutants, the government has formulated a series of remediation measures, the relevant enterprises to effectively assume responsibility for the theme of pollution control, ensure the completion of the task within the stipulated time. For within the specified time still can not meet the requirements of enterprise and equipment, the relevant departments will be severely punished according to law.

Other Products