10 Ton Gas Fired Hot Water Boiler

Oil 10 ton fired hot water boiler structure design is how to avoid the danger of explosion of fuel hot water boiler hot water boiler dedicated micro-controller configuration, large-screen full Chinese LCD screen with super bright backlight, day or night, the boiler operation status is clearly visible. Display complete: circulating pump, the operation of the burner, the boiler water temperature, water level, the current time, alarm records, ranging boiler operating state; easy setup: the boiler power, the operator can freely enter key 6 when operating parameters for the standby state (set) into the operating state (power on), the state out of operation (stop), the random standby state is set; functional: arbitrarily set the current time, alarm temperature, the maximum temperature of water, The lower limit of water temperature, the temperature of the circulation pump is turned on, the circulation pump shutdown temperature, the boiler switch time (divided into four time periods) and other operating parameters. The operator usually just press the start key to boot, press the stop button to stop, very simple. Oil hot water boiler structure design is how to avoid the danger of explosion by the fuel pressure hot water boiler structural design, top with a through large pores, boiler work under pressure, away from the danger of explosion; boiler furnace using computer simulation to optimize the design, fully optimize the size of the boiler, the form of coordinated appearance. Vertical CLHS mounted boiler combustion at the burner, the fuel is combusted within a slight positive pressure furnace, the flue gas temperature in the furnace radiation heat transfer, convective heat transfer and then enter the pyrotechnics, smoke box is discharged through the last. Smoke tube baffle is inserted, the smoke evacuation slow speed, heat strengthening, fuel combustion furnace to ensure the greatest degree of heat generated water, greatly improve the thermal efficiency of the boiler; CWNS horizontal boiler with full wet back three return structure, the flue gas flow length, reduced exhaust gas temperature, the whole corrugated furnace provided, so that the flame produced a strong turbulence to improve the heat transfer coefficient strength, and effectively prevent the metal due to thermal expansion and contraction result in reduced equipment life; large-diameter cigarette tube and macropores bridge the gap, the boiler at equal time scale coating thin and easy to clean.

Use 10 ton fired hot water boiler and hot water boiler structural principle profiles include hot water boiler electric water boilers, hot water boiler fuel, gas hot water boilers and coal-fired hot water boilers, hot water boilers that produce hot water boilers, it refers to the use of fuel the heat released by combustion or other thermal energy (e.g., electrical energy, solar energy, etc.) the water was heated to a nominal temperature of a thermal device. Use hot water boiler and hot water boiler heating bath mainly two purposes. Hot water boiler by circulating hot water circulation pump hot water holding tank, the tank hot water heating cycle can be achieved bath object; hot water boiler by circulating hot water circulation pump heating conduit, through the heat sink (radiator) people can achieve heating requirements; hot water boiler and hot water circulating pump with heat exchanger can be achieved bathing and heating dual function. Principle structure of the natural circulation of the hot water boiler hot water boiler, inlet and outlet are taken over from the top of the drum, the water from the water distribution pipe guide and drop into the front side lower header pipe, through the waterwall tubes heating rise. The front drum, rear end plate is provided with impermeable boundary falling rising flow, only the lower half of the drum cross-impermeable partition plate. For the forced circulation, the water access to the front end of the lower header, the front drum increases to upper waterwall tubes (waterwall downcomer Cancellation time), and then transferred to the waterwall tubes downcomer side to side lower header, then into the side of the cloth water wall tube rose to the drum, and from the front row convection bank down to the next drum, and finally between the upper and lower drum and several circuitous flow of water from the rear end of the drum. No circulation boiler with economizer.

Industrial boiler energy-saving technological transformation of existing problems in industrial boiler energy-saving technological transformation of Question 1, the lack of innovation, application of energy-saving boiler mature, molding technology and equipment, such as: increased flue gas heat recovery unit, blowers inverter , condensate recovery and other conventional energy-saving measures is essentially a general condition; and the need for structural changes in energy-saving measures, such as fractional bed combustion of coal and boiler furnace arch transformation techniques, etc., are rare; as transformation project new principle, a new device, oxyfuel technology, high temperature air combustion technology, spray pulverized coal combustion technology (+ supernatant layer combustion boiler combustion mode), condensing heat recovery technology, new energy technologies dust ash and water treatment equipment, is very few. In general, innovation is not enough, the technical content needs to be improved. 2, part of the boiler is not fully considered in the transformation process, but simply changing the burner, the combustion gas flow distribution and does not match the corresponding surface of the heating boiler, the boiler furnace wall insulation and sealing transformation. There is poor combustion boiler, insufficient output, higher exhaust temperature problem, can not achieve the purpose of energy saving. 3, the waste heat boiler using high temperature organic heat required for thermal processes, a boiler generally at 200 ℃ 300 ℃, the exhaust gas temperature of the boiler is usually too high, excessive. In order to meet requirements of energy saving, companies often mounted in the boiler backpass evaporator or a hot water tank, flue gas waste heat recovery, reducing the exhaust temperature. But most of the heat generated in the production process does not require little energy. 4, statistical analysis of experimental data shows that there are many problems inefficiencies run natural gas boiler. The main concern of automatic combustion control, early production debugging is not in place, and so on. Gas boiler gas and incomplete combustion abnormal increase in heat loss caused by high temperature exhaust gas is the direct cause of poor operating efficiency. However, the use of clean energy natural gas boiler, generally higher thermal efficiency, energy saving difficult. Corporate restructuring investment funds enthusiasm is not high.

AMD Power were to buy 10 tons of steam and one 4 tons of steam condensing steam boiler fuel gas from the company for cell processing company production and construction. From the analysis of the demand to the boiler factory, by the company solely responsible for AMD Power fully demonstrated the company's confidence in me, the smooth progress of bilateral cooperation.